electromaniacs.com - News Feeds

News Feeds

News Feeds
New TI Semiconductor Products
View all TI semiconductor products released within the last 110 days.
Audio TLV320AIC3262 Low Power Stereo Codec with miniDSP, Integrated Class-D Speakers, Earpiece Driver, DirectPath The TLV320AIC3262 (also referred to as the AIC3262) is a flexible, highly-integrated, low-power, low-voltage stereo audio codec. The AIC3262 features digital microphone inputs and programmable outputs, PowerTune capabilities, enhanced fully-programmable miniDSP, predefined and parameterizable signal processing blocks,... Audio TPA2029D1 3-W Mono Class-D Amplifier With Smart Gain AGC/DRC The TPA2029D1 is a mono, filter-free Class-D audio power amplifier with dynamic range compression (DRC) and automatic gain control (AGC). It is available in a 1.63 mm x 1.63 mm WCSP package. The DRC/AGC function in the TPA2029D1 can be enabled and disabled. The DRC/AGC function is configured to automatically... Interface SN65LVPE502 Dual Channel USB3.0 Redriver/Equalizer The SN65LVPE502 is a dual channel, single lane USB 3.0 redriver and signal conditioner supporting data rates of 5.0Gbps. The device complies with USB 3.0 spec revision 1.0, supporting electrical idle condition and low frequency periodic signals (LFPS) for USB 3.0 power management modes. Programmable EQ, De-Emphasis... Switches and Multiplexers TS3A27518E-Q1 Automotive Catalog 6-Bit, 1-of-2 Mux/Demux with 240 MHz Bandwidth The TS3A27518E-Q1 is a 6-bit 1-of-2 mux/demux designed to operate from 1.65 V to 3.6 V. This device can handle both digital and analog signals, and signals up to V+ can be transmitted in either direction. The TS3A27518E-Q1 has two control pins, each controlling three 1-of-2 muxes at the same time, and an enable pin... Interface SN65LVPE502CP Dual Channel USB3.0 Redriver/Equalizer The SN65LVPE502CP is a dual channel, single lane USB 3.0 redriver and signal conditioner supporting data rates of 5.0Gbps. The device complies with USB 3.0 spec revision 1.0, supporting electrical idle condition and low frequency periodic signals (LFPS) for USB 3.0 power management modes. ... Amplifiers and Linear PGA308-Q1 Automotive Catalog Single Supply, Auto-Zero Sensor Amplifier w/Programmable Gain & Offset The PGA308-Q1 is a programmable analog sensor signal conditioner. The analog signal path amplifies the sensor signal and provides digital calibration for offset and gain. Calibration is done via the 1W pin, a digital One-Wire, UART-compatible interface. For three-terminal sensor modules, 1W may be connected to VOUT... Power Management TLC59711 12-Channel, 16-Bit, ES-PWM RGB LED Driver with 3.3V Linear Regulator and Watchdog Timer The TLC59711 is a 12-channel, constant-current sink driver. Each output channel has individually adjustable currents with 65536 PWM grayscale (GS) steps. Also, each color group can be controlled by 128 constant-current sink steps with the global brightness control (BC) function. GS control and BC are accessible via a two-wire... Amplifiers and Linear PGA450-Q1 Automotive Ultrasonic Sensor Signal Conditioner The PGA450-Q1 is a fully integrated interface device for ultrasonic transducers used in automotive park distance or object detection applications. It incorporates these system blocks: voltage regulators, a 12-bit SAR ADC, an 8-bit microcontroller, a digital band-pass filter, a DAC, dual NMOS low-side drivers,... Power Management BQ27520-G3 System-Side Impedance Track? Fuel Gauge With Integrated LDO The Texas Instruments bq27520-G3 system-side Li-Ion battery fuel gauge is a microcontroller peripheral that provides fuel gauging for single-cell Li-Ion battery packs. The device requires little system microcontroller firmware development. The resides on the system’s main board and manages an embedded battery... Power Management TLV71128518D Dual, 200mA Output, Low Noise, High PSRR, Low-Dropout Regulator with Active Pull-Down The TLV710 and TLV711 series of dual, low-dropout (LDO) linear regulators are low quiescent current devices with excellent line and load transient performance. These LDOs are designed for power-sensitive applications. These devices provide a typical accuracy of 2% over temperature. The TLV711 series provides an... Microcontrollers TMS320F280230 Piccolo Microcontroller The F2802x0 Piccolo family of microcontrollers provides the power of the C28x core coupled with highly integrated control peripherals in low pin-count devices. This family is code-compatible with previous C28x-based code, as well as providing a high level of analog integration. An internal voltage... Power Management TPS82672 600-mA, High-Efficiency MicroSiP? Step-Down Converter (Profile <1.0mm) The TPS8267x device is a complete 600mA, DC/DC step-down power supply intended for low-power applications. Included in the package are the switching regulator, inductor and input/output capacitors. No additional components are required to finish the design. The TPS8267x is based on a high-frequency synchronous... Power Management TLV620612-Q1 Automotive Catalog 3MHz, 2A Step-Down Converter in 2x2 SON Package The TLV620612-Q1 is a highly efficient, synchronous step-down, dc-dc converter with a 1.2-V fixed output voltage. It provides up to 2 A of output current. With an input voltage range of 2.9 V to 5.5 V, the device is a perfect fit for power conversion from a 5-V or 3.3-V system supply rail. The... Power Management BQ24166 2.5A, Dual-Input, Single Cell Switchmode Li-Ion Battery Charger with Power Path Management The bq24165, bq24166 and bq24167 are highly integrated single cell Li-Ion battery charger and system power path management devices targeted for space-limited, portable applications with high capacity batteries. The single cell charger has dual inputs which allow operation from either a USB port or higher power input supply... Interface SN75DP126 DisplayPort 1:2 Re-Driver Switch with TMDS Translator The SN75DP126 switches one Dual-Mode DisplayPort (DP++) input to one Dual-Mode DisplayPort (DP++) sink output or one HDMI/DVI sink output. The HDMI/DVI output has a built-in level translator compliant with DVI 1.0 and HDMI 1.4b standard TMDS signaling, and is specified up to a maximum data rate of 3.4 Gbps, supporting resolutions... Power Management TPS65197 8-Channel Level-Shifter supporting different Charge-Sharing Methods and Panel Discharge The TPS65197 is an 8-channel level-shifter with discharge function intended for use in LCD display applications such as TVs and monitors. The device converts the timing-controller (T-CON) logic-level signals to the high-level signals needed by the gate-in-panel (GIP) display. The clock outputs, CLKOUTx, support... Power Management CSD25211W1015 P-Channel NexFET? Power MOSFET The device has been designed to deliver the lowest on resistance and gate charge in the smallest outline possible with excellent thermal characteristics in an ultra low profile. ... Digital Signal Processor & ARM Microprocessor Platforms TMS320C6657 Fixed and Floating Point Digital Signal Processor The TMS320C6657/55 Multicore Fixed and Floating Point Digital Signal Processors are based on TI's KeyStone multicore architecture. The C6657 is integrated with two C66x DSP CorePacs running at 0.85, 1.0 or 1.25 GHz. The C6655 contains one C66x DSP CorePac running at 1.0 or 1.25 GHz. These devices support high-performance... Power Management TPS7A6533-Q1 Automotive Catalog 300-mA 40-V Low-Dropout Regulator With Ultra-Low Quiescent Current The TPS7A65xx is a series of low dropout linear voltage regulators designed for low power consumption and quiescent current less than 25 µA in light load applications. These devices feature an integrated over-current protection and are designed to achieve stable operation even with low-ESR ceramic output capacitors.... Data Converters ADS1292R 2-Channel, 24-Bit Analog-To-Digital Converter w/Integrated Respiration Impedance and ECG Front End The ADS1291, ADS1292, and ADS1292R are multichannel, simultaneous sampling, 24-bit, delta-sigma (ΔΣ) analog-to-digital converters (ADCs) with a built-in programmable gain amplifier (PGA), internal reference, and an onboard oscillator. The ADS1291, ADS1292, and ADS1292R incorporate all features commonly required... Power Management BQ3050 SBS 1.1-Compliant 2S to 4S Battery Gas Gauge & Protection The bq3050 device is a fully integrated, single-chip, pack-based solution that provides a rich array of features for gas gauging, protection, and authentication for 2-series, 3-series, and 4-series cell Li-Ion and Li-Polymer battery packs. Using its integrated high-performance analog peripherals, the bq3050 device... Power Management TLV62080 1.2A High Efficiency Step Down Converter in 2x2mm SON Package The TLV62080 device is a synchronous step down converter with an input voltage range of 2.5V to 5.5V. The TLV62080 focuses on high efficient step down conversion over a wide output current range. At medium to heavy loads, the converter operates in PWM mode and automatically enters Power Save Mode operation at light... Power Management TPS7A6150-Q1 Automotive Catalog 300-mA 40-V Low-Dropout Regulator With Ultra-Low Quiescent Current and enable The TPS7A60xx/TPS7A61xx is a series of low dropout linear voltage regulators designed for low power consumption and quiescent current less than 25 µA in light load applications. These devices feature an integrated over current protection and are designed to achieve stable operation even with low-ESR ceramic capacitors.... Interface TXS02326A Dual-Supply 2:1 SIM Card Multiplexer/Translator with Automatic Detect The TXS02326A is a complete dual-supply standby Smart Identity Module (SIM) card solution for interfacing wireless baseband processors with two individual SIM subscriber cards to store data for mobile handset applications. It is a custom device which is used to extend a single SIM/UICC interface to support two SIMs/UICCs. ... Amplifiers and Linear DRV8836 1.5A Low Voltage Stepper or Single/Dual Brushed DC Motor Driver (PWM or PH/EN Ctrl) The DRV8836 provides an integrated motor driver solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications. The device has two H-bridge drivers, and can drive two DC motors or one stepper motor, as well as other devices like solenoids. The output driver block... Power Management TPS2060C Dual-Channel, Current-Limited, Power-Distribution Switch The TPS20xxC dual power-distribution switch family is intended for applications such as USB where heavy capacitive loads and short-circuits may be encountered. This family offers multiple devices with fixed current-limit thresholds for applications between 1 A and 2 A. The TPS20xxC dual family limits the... Power Management TLV71713P 150mA, Single Output, Low Noise, Low-Dropout Regulator for Portable Devices The TLV717xx series of low-dropout (LDO) linear regulators are low quiescent current LDOs with excellent line and load transient performance and are designed for power-sensitive applications. These devices provide a typical accuracy of 0.5%. The TLV717xx series offer current foldback that throttles down the output current with... Power Management TLV7113030D Dual, 200mA Output, Low Noise, High PSRR, Low-Dropout Regulator with Active Pull-Down The TLV710 and TLV711 series of dual, low-dropout (LDO) linear regulators are low quiescent current devices with excellent line and load transient performance. These LDOs are designed for power-sensitive applications. These devices provide a typical accuracy of 2% over temperature. The TLV711 series provides an... Amplifiers and Linear DRV8834 2.2A Low Voltage Stepper w/ 32-step Indexer or Dual Brushed DC Motor Driver (Indexer or PH/EN Ctrl) The DRV8834 provides a flexible motor driver solution for toys, printers, cameras, and other mechatronic applications. The device has two H-bridge drivers, and is intended to drive a bipolar stepper motor or two DC motors. The output driver block of each H-bridge consists of N-channel... Amplifiers and Linear DRV8835 1.5A Low Voltage Stepper or Single/Dual Brushed DC Motor Driver w/ Dual Supplies (PWM or PH/EN Ctrl) The DRV8835 provides an integrated motor driver solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications. The device has two H-bridge drivers, and can drive two DC motors or one stepper motor, as well as other devices like solenoids. The output driver block... Data Converters AMC1100 4.25kVPEAK Isolated Amplifier for e-metering The AMC1100 is a precision isolation amplifier with an output separated from the input circuitry by a silicon dioxide (SiO2) barrier that is highly resistant to magnetic interference. This barrier has been certified to provide galvanic isolation of up to 4250 VPEAK, according to UL1577 and IEC60747-5-2. Used in conjunction with... Power Management TPS62080A 1.2A High Efficient Step Down Converter in 2x2mm SON Package The TPS6208x devices are a family of high frequency synchronous step down converters. With an input voltage range of 2.3V to 6.0V, common battery technologies are supported. Alternatively, the device can be used for low voltage system power rails. The TPS6208x focuses on high efficient step down conversion over a wide... Audio INA2134-EP Enhanced Product Audio Differential Line Receiver 0dB (G = 1) The INA2134 is a differential line receiver consisting of high performance op amps with onchip precision resistors. The device is fully specified for high performance audio applications and has excellent ac specifications, including low distortion (0.0005% at 1 kHz) and high slew rate (14 V/ms), assuring good dynamic... Interface ISO7421E-Q1 Automotive Catalog Low-Power Dual Channel Digital Isolators The ISO7421E-Q1 provides double galvanic isolation of up to 2.5 KVrms for 1 minute per UL. This digital isolator has two isolation channels in a bi-directional configuration. Each isolation channel has a logic input and output buffer separated by a silicon oxide (SiO2) insulation barrier. Used in conjunction with... Power Management LM3253 High Current Step Down DC/DC converter for 2G/3G/4G Power Amplifiers The LM3253 is a DC-DC converter optimized for powering multi-mode 2G/3G/4G RF power amplifiers (PAs) from a single Lithium-Ion cell. The LM3253 steps down an input voltage from 2.7V to 5.5V to a dynamically adjustable output voltage of 0.4V to 3.6V. The output voltage is set through a VCON analog input that adjusts... Audio PCM5102-Q1 Automotive Catalog 112dB Stereo DAC with 2VRMS output and Integrated Audio PLL The PCM5102-Q1 is a monolithic – SNR: 112 dB (Typical) CMOS integrated circuit that include a stereo digital-to-analog converter and additional support – Dynamic range: 112-dB (typical) circuitry in a small TSSOP package. The PCM5102-Q1 – THD+N: –93 dB at –1 dBfs (typical) uses the latest generation... Power Management BQ294512 Overvoltage Protection Device for 2- to 3-Cell Li-Ion Batteries, with 4.40v OVP The bq2945xy family of products is a secondary level voltage monitor and protector for Li-Ion battery pack systems. Each cell is monitored independently for an overvoltage condition. Based on the configuration, an output is triggered after a fixed delay if any one of the two or three cells has an overvoltage condition.... Power Management TPS62091 3A,2.5V to 6V input, up to 97% efficiency, Synchronous Step Down Converter with DCS? Control The TPS6209x device family is a high frequency synchronous step down converter optimized for small solution size, high efficiency and suitable for battery powered applications. To maximize efficiency, the converter operates in PWM mode with a nominal switching frequency of 2.8 MHz/1.4 MHz and automatically enters... Amplifiers and Linear THS4531 Ultra low power 0.25mA, RRO, fully differential amplifier The THS4531 is a low-power, fully-differential op amp with input common-mode range below the negative rail and rail-to-rail output. The device is designed for low-power data acquisition systems and high density applications where power consumption and dissipation is critical. The device features accurate output common-mode... Amplifiers and Linear OPA1654 Sound Plus Low Noise and Distortion, General-Purpose, FET-Input Audio Op Amps The OPA1652 (dual) and OPA1654 (quad) FET-input operational amplifiers achieve a low 4.5 nV/√Hz noise density with an ultralow distortion of 0.00005% at 1 kHz. The OPA1652 and OPA1654 op amps offer rail-to-rail output swing to within 800 mV with 2-kΩ load, which increases headroom and maximizes dynamic range. These... Power Management BQ24158 Fully Integrated Switch-Mode One-Cell Li-Ion Charger with Full USB-Compliance, VOVP=6.5v The bq24153A/6A/8/9 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates a synchronous PWM controller, power... Interface SN75LVDS83C FlatLink 10-85MHz Transmitter The SN75LVDS83C FlatLink transmitter contains four 7-bit parallel-load serial-out shift registers, a 7X clock synthesizer, and five Low-Voltage Differential Signaling (LVDS) line drivers in a single integrated circuit. These functions allow 28 bits of single-ended LVTTL data to be synchronously transmitted over five... Power Management TPS7A7200 2A, Single Output, Very Low Input, Configurable Fixed (0.9 to 5.0V) Low-Dropout Linear Regulator The TPS7A7200 low-dropout (LDO) voltage regulator is designed for applications seeking very-low dropout capability (180 mV at 2 A) with an input voltage from 1.5 V to 6.5 V. The TPS7A7200 offers an innovative, user-configurable, output-voltage setting from 0.9 V to 3.5 V, eliminating external resistors and any associated error.... Power Management TLV1117LV25 1A, Positive Fixed Voltage Low-Dropout Linear Regulator The TLV1117LV series of low-dropout (LDO) linear regulators is a low input voltage version of the popular 1117 voltage regulator. The TLV1117LV is an extremely low-power device that consumes 500 times lower quiescent current than traditional 1117 voltage regulators, making it suitable for applications that... Audio TLV320AIC3212 Low Power Stereo Codec with Integrated Class-D Speakers, Earpiece Driver, DirectPath The TLV320AIC3212 (also referred to as the AIC3212) is a flexible, highly-integrated, low-power, low-voltage stereo audio codec. The AIC3212 features digital microphone inputs and programmable outputs, PowerTune capabilities, selectable audio-processing blocks, predefined and parameterizable signal processing blocks,... Power Management TPS82695 500-mA, High-Efficiency MicroSiP? Step-Down Converter (Profile <1mm). Vout=2.5V The TPS8269xSIP device is a complete 500mA, DC/DC step-down power supply intended for low-power applications. Included in the package are the switching regulator, inductor and input/output capacitors. No additional components are required to finish the design. The TPS8269xSIP is based on a high-frequency synchronous... Amplifiers and Linear DRV8818 2.5A Bipolar Stepper Motor Driver with On-Chip 1/8 Microstepping Indexer (Step/Dir Ctrl) The DRV8818 provides an integrated stepper motor driver solution for printers, scanners, and other automated equipment applications. The device has two H-bridge drivers, as well as microstepping indexer logic to control a stepper motor. The output driver block for each consists of N-channel power MOSFETs... Interface PCA9515B Dual Bidirectional I2C Bus and SMBus Repeater, PCA9515B The PCA9515B is a BiCMOS integrated circuit intended for I2C bus and SMBus systems applications. The device contains two identical bidirectional open-drain buffer circuits that enables I2C and similar bus systems to be extended without degrading system performance. The dual bidirectional I2C buffer is... Power Management TPS2062C Dual-Channel, Current-Limited, Power-Distribution Switch The TPS20xxC dual power-distribution switch family is intended for applications such as USB where heavy capacitive loads and short-circuits may be encountered. This family offers multiple devices with fixed current-limit thresholds for applications between 1 A and 2 A. The TPS20xxC dual family limits the... Power Management TLV71712P 150mA, Single Output, Low Noise, Low-Dropout Regulator for Portable Devices The TLV717xx series of low-dropout (LDO) linear regulators are low quiescent current LDOs with excellent line and load transient performance and are designed for power-sensitive applications. These devices provide a typical accuracy of 0.5%. The TLV717xx series offer current foldback that throttles down the output current with...

[ Back ]

Sponsored Links